JASO D General Rules of Environmental Testing Methods for Automotive Revision: Edition, ; Published Date: January ; Status: Not Active, . simulate this condition include the U.S.’s ISO pulse 1 and 3a, and Japan’s JASO D, standard type B and E. Each peak voltage for these tests is. The MPG S21 has a built-in battery switch to interrupt the DC supply voltage and is specifically designed for JASO. D, test pulses E1 and E2.
|Published (Last):||19 November 2005|
|PDF File Size:||10.59 Mb|
|ePub File Size:||5.5 Mb|
|Price:||Free* [*Free Regsitration Required]|
Some test results indicate, if a noise suppressor condenser is installed in parallel to the jaaso supply circuit, it will constitute the major electrostatic capacity of the power supply circuit, and will affect on the generation of arc discharge.
Any equipment installed on body or the spring of suspension system, the vibration of which is relatively high. Such devices, therefore, may be excluded from this standard, but it is desirable that the test methods specified in this standard are applied to those equipments.
Points revised o individual provision and f supplemental explanation thereof 3. Lower the temperature inside the chamber gradC ually, when it has reached jawo – 30 Okeep the equipment for 1 -t 0.
Some examples are given below for reference of temperature setting for these equipment.
JASO D 94 datasheet & applicatoin notes – Datasheet Archive
It would be difficult to get test gear. Herein those JASOs standards, the testing conditions were dicided to be specified as the general conditoins representing it. Should so wide range of difference of temperatures be specified, it would be regarded as a kind of thermal shock test. The differences between the JIS C and JIS C are that the former is a test in which mist is continuously sprayed, while the latter is a cycle test in which mist spraying and stopping it are altertively repeated.
Clocks, navigation device, etc. The Type A and Type C shall be applied to destructive test, and the Type B shall be applied to test for mal-operation. Purpose This standard aims to establish a unified test method in order to evaluate the performance of automotive electronic equipment under various environmental conditions. The test order of setting temperature is not particularly specified.
JSS// – NOISE LABORATORY CO.,LTD.
The test aims to evaluate the voltage resistance against the overvoltage generated in case above mentioned. Further, for comprehensive evaluation of the equipment including the effects of wiring and grounding when it is fitted on a vehicle, a test impressing electromagnetic field directly is sometimes necessary as the technical report of SAE J for instance.
Carry out the test pattern shown in Fig. Therefore, the time required of release was specified so as to be equal to 10 minutes to the maximum value as long after such maximum value on the condition at normal room temperature and under normal room humidity had been decked to be used.
Raytac Module MDBT40/MDBT40-P Certified Automotive Standard JASO D001-94
Care must be taken because batteries may explode if sparks are generated near them. As for the details such as kinds of signal lines indicated in the test circuit, etc. Test conditions are specified separately for Type A impressing at terminalsand Types B and C impressing at operating portion according to the difference of the conditions the equipment is handled in use or the happening of the equipment with electrostatic discharge. Conducted electromagnetic tests are divided into two frequency bands of 30Hz to 50Hz and 50kHz to MHz, while the radiated electromagnetic tests are divided into three tests, test by magnetic field of 30Hz to 15kHz and tests by electric fields of 1MHz to MHz and MHz to MHz.
However, since there was not any testing specified in this standard, the minor deviation of testing voltage at which is important, it was decided to provide a provision to specify that the testing voltage shall be applied, which shall be monitored so as to be correct by means with any voltmeter of accuracy in the class of 0. Specified values of resistor and capacitor shall be true value, not designated value.
Number of impressions is specified as 3 times or more, but about jaxo times are desirable. In order to avoid a duplication of the provisions, this test was removed from this D Any equipment installed on engine, the vibration of which is relatively low. Confirm the appearance, etc. The test duration suitable d001-944 actual conditions may, therefore, be selected under the agreement between the persons concerned, out of the three durations mentioned above, because the test duration may be shortened or be necessary to be extended according to the kind of equipment to be tested.
In respect of the time required of test, the 96 hours 4 days was decided to be designated as the condition representing them. Then, make kaso temperature gradually approached to other temperature and record in like manner. As for the intensity of interference electromagnetic field to be impressed in the test, the numerical values of 0.
After the test above, the test in 5. Power supply device Power source supply device from which required DC power is stably available battery and any other similar equipment, the internal impedance of which is so low as same as the batterythe supplied voltage is variable within a range from 8 to 38V, the voltage fluctuation of the power supplied is f within a range of k 0.
Connect the input and loading device to the test speciment so that the equipment may operate during the test; connect the assembly to the test apparatus specified in 5. In case of the equipment, the heat mass of which are utmost high, the duration of time for holding at low temperature and the time required of release in constant temperature and humidity chamber may be optionally fixed in accordance with the agreement made between the persons concerned.
The additional operations shall be carried out subsequent thereto as specified hereunder.: Other details of the tests are left to the agreement between parties. The test results are proper to the set test conditions, and it is difficult to evaluate as normal characteristics of a specimen.
This d010-94 should be specially applied against the liquid crystal displays, etc. JAS0 D Fig.