Graupner: MC, MC, MC, MC, MC, MC, MC, MC/20, es in Übereinstimmung mit dieser Anleitung mit vorgeschriebenr Spannung. Bowdenzuginnenrohr auf 15mm ab und kleben diese mit Sekundenkleber in den passen Sie den Ausschlag über den Sender an (Computersender der mc. Thank you very much for purchasing the Graupner mc HoTT .. 15 / _jh_V1_de. PC COM Port connection. Through this socket it is also possible to.
|Published (Last):||4 October 2011|
|PDF File Size:||9.61 Mb|
|ePub File Size:||18.18 Mb|
|Price:||Free* [*Free Regsitration Required]|
The Transmitter can be determined by anlitung crystal. Page 55 Fixed Wing Models Practical Procedure Basic Adjustment Graupnwr that is not the case, then one proceeds as follows: Descending Flight Setting Alternative Flight Setting Important Notes During the previous setting it was assumed that any For special applications you can program an Before starting the engine you should make sure that external switches possibly attached for throttle and alternative flight ankeitung, which can be switched to throttle selector switch is in the start position, pitch curve change-over were in the basic position, Can some one help with that?
Operating Instructions The resistance to movement of the control stick can Opening the Transmitter case Changing the proportional control sticks and changing the centring force. Possibly only useful to activate mixing programs on the MC, on my MC i can also use them channels. Newly developed LCD multi-data display with integrated static driver for precise, clear digital display.
Throttle Curve Throttle Curve Throttle Curve Low, Middle, High access via Set-Up Menu Three different profiles for the carburettor response Setting can be adjusted and called up in flight by external After selection of the point required using the switches; the function of the throttle pre-select is button and operation of the appropriate CH SEL included in this changeover.
Pitch Curve Pitch Curve Pitch Curve Low, Middle, High access via Set-Up Menu Four different profiles for the collective pitch Setting response can be adjusted and called up in flight by After selection of the point required using the external switches.
Is gonna be used for an RC submarine project. Md permits independent adjustment of the aileron deflections upward and downward, which allows a differential mixer to be used. Page 95other small accessories or grauner accommodate sunglasses etc. I know is possible because I opened the case and I see these ]http: For models with a V-tail, “VTL”, must be used to mix the functions of elevator and rudder.
GRAUPNER MC PROGRAMMING MANUAL Pdf Download.
Page 29 Fixed Wing Models Comments to this Manuals Your Name. If I could find wit a long or flat arm wheel be nice. Page 97 This is fitted next to the receiver. Elevator Anlejtung Dual-Rate and Exponential for: A switch connected to socket 7 of the transmitter board, allows this function to be changed between two anleifung “SF0” Page 70 Throttle and Collective Pitch curves: Any information is valuableso Please feel free to share with me what ever You have.
So, I will get the switch and trim the lever down so I can slip a brass tube over it. General permission for a Radio concerning the remote control of models Auxiliary information for manufacturers, trading companies, system approvals, Saarbrucken, for examination, and the salesmen and purchasers examination demonstrates that the design corresponds to the appropriate technical regulations FTZ guideline 17 R for I have an MC19s.
Fasten the NAUTIC modules Length adjustment of the control sticks Assembly of the Transmitter Carriers Insert the module into the intended location and that The length of the control sticks can be adjusted up to The transmitter can be equipped with the transmitter check it fits correctly. Table of Contents Add to my manuals Add.
Was the only one I get afford to buy. Aileron Roll Dual-Rate and Exponential for: So if You have some directions for me don’t hesitate to tell me. Connections to the receiver Ch 1 to 8 The servos must be connected to the receiver outputs as shown below: Manual in English for MC Also included is a ready made mixer for Elevator Flap mixing.
GRAUPNER mc-16 Programming Manual
The MC can freely assign each input to any of up to 12 channels. Page 53 Fixed Wing Models For the 3-way switches oder potentiometer use pin 1 and 3 the outer ones to pin 1 and 5 the outer ones at the 5-pin connector and pin 2 middle one on pin 2 or 4 on the 5-pin connector, turning the connector means reversing the channel. Page of Go. For the graupnef or 2-way switches most of them are 2-way use pin 1 and 2 one outer and the middle one for the 2-pin connector.
Enter text from picture: I thought maybe was made only pieces and nobody cares to put graunper internet some info. Set-Up Menu General notes if necessary also over Ailerons. If anlwitung do you think it can be somehow send to me on email address? Al I need is what type of components are suitable for and If is necessary to make some settings on it.
Setting mix proportion and mix direction. I know was made around year not OLDhuhand I thought is my last chance to open a thread here about these RC station. Page 9 Fasten the NAUTIC modules Length adjustment of the control sticks Assembly of the Transmitter Carriers Insert the module into the intended location and that The length of the control sticks can be adjusted up to The transmitter can be equipped with the transmitter check it fits correctly.
Page 85 Receiver Requirements Note: Regarding these I spent all my day 7 to 8 hours!!! Select the standard Since these are not influenced by the dual rate and You have concluded the basic programming of the model type “FL” in the system menu. Mybe I’m not so skiled with internet. Page 71 Descending Flight Setting Alternative Flight Setting Important Notes During the previous setting it was assumed that any For special applications you can program an Before starting the engine you should make sure that external switches possibly attached for throttle and alternative flight setting, which can be switched to throttle selector switch is in the start position, pitch curve change-over were in the basic position, The extremely high contrast enables, even with bright sunlight, a precise check of the functions displayed in the transmitter display such as operating voltage, input data, mixer functions, settings, direction of rotation, trim and programming I upgraded my MC with 4 3-way switches: