Evertz HD Pdf User Manuals. View online or download Evertz HD User Manual. HD, HD and HD Video PassPort™. 1RU Multi-Path Video Converter and Frame Synchronizer The HD integrates four . Evertz’s HD and more (English). in BROADCAST ENGINEERING – INDIANAPOLIS THEN OVERLAND PARK KANSAS-; 52, 8; BROADCAST .
|Published (Last):||25 December 2017|
|PDF File Size:||19.51 Mb|
|ePub File Size:||9.72 Mb|
|Price:||Free* [*Free Regsitration Required]|
Evertz Microsystems expressly prohibits the use of this manual for any purpose other than the operation of the device. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating eevertz maintenance Servicing instructions in the literature accompanying the product. Use of unshielded plugs or cables may cause radiation interference. Evertz products are for informational use only and are not warranties of future performance, either expressed evertx implied.
The only warranty offered by Evertz in relation to this product is the Evertz standard limited warranty, stated in the sales contract or order confirmation form. Controlling egertz Test Signal Controlling the Analog Audio Output Setting the Output V Start Setting the Output V Stop Setting the H Slew Rate Limit Setting the V Slew Rate Limit Setting the Reference Format Setting the Reference Mode Configuring the Test Generator HD except that both processing paths must be fed from the same input video signal.
HD Block Diagram Revision 0. The following sections will give an overview of each hs2014 and their function including any relevant pin-out information. Rear View of HD 2.
GPIs are active low and edge sensitive rather evdrtz level sensitive. DB15 connector and breakout cable pin-out information is provided in the tables below. Analog audio is interfaced using a 36 pin analog audio terminal block. Refer to the breakout cable diagram in Figure Functionality depends on the installed flex module. Coax Inputs Number of Inputs: Fiber Inputs Number of Inputs: Mono signals, balanced analog audio Type: Removable terminal strip Connector: Quick access control buttons are located on the left hand side of the front panel to enable quick and easy changes to core processing parameters on a per path basis.
Selecting the Processing Path Output Video Hf2014 Once a particular processing path has been selected for control as per section 4. The currently selected video format will automatically appear once the FMT button is pushed. Selecting the Aspect Ratio Conversion Mode for the Processing Path Once a particular processing path has been selected for control per section 4.
Evertz HD2014 User Manual
Adjusting the Video Proc for the Processing Path Once a particular processing path has been selected for control as per section 4. The list of available video proc controls for relevant processing path will then appear.
When the AA OUT button is pressed on the front panel, the user will immediately be brought to the menu tree for the analog audio outputs.
In the HD, there will be four selections available to the user, one for each of the four processing paths in the unit. In the HD, there will be two selections available to the user, one for each of h2014 two processing paths in the unit. To access the core video processing parameters, navigate the engineering menu as follows: The HD has four internal video processors.
The HD and the HD has two internal video processors. For the sake of brevity, only controls for PATH hd0214 will be shown in the following sections. Enabling Closed Captions The CC Enable control allows the user to enable and disable caption insertion on the converter outputs.
When the Captions control is enabled, any closed h2d014 will be mapped to line 21 if the output video is SD, or to the designated HD write line if the output video is HD. Setting the Type of Deinterlacer The user can adjust basic operating mode for the video de-interlacing used in the video processors with the De-Interlacer Type control.
Optimal processing for normal video content is achieved when everrtz to Auto. Setting SD Blanking With the SD Blanking control, the user can adjust which standard definition lines will be blanked prior to up-converting the signal.
All active everrz lines up to and including the selected line number will be blanked. Converters are not capable of temporal processing, so it will not convert between Setting the Noise Reduction Level The Noise Reduction control manages the level of noise reduction to apply to the video signal. The selection levels automatically set the motion detection threshold and the aggressiveness of the filters to remove noise.
When enabled, the module will clip any illegal levels of R, G, and B individually to black and white levels. Many of the standard aspect ratio conversions are listed as pre-defined options that may be selected. Setting the Input H Start The Input H Start control defines jd2014 starting horizontal portion of the input image that will be processed to the output.
Input Evvertz Start does not have any effect when the pre-defined aspect ratios are used. Setting the Output H Start The Output H Start control determines where to place the selected portion of the input image onto the output video raster.
Setting the Output V Stop The Output V Stop rvertz determines where to place the selected portion of the input image onto the output video raster. The Output V Stop control defines the ending vertical position for video content on the output image raster. This control manages the amount of aliasing that the vertical scaler allows to pass from its input to output when performing scaling and aspect ratio conversion.
Setting the V Phase With the V Phase Offset control, you can set the eevertz timing of the output video with respect to the reference. This controls reports the status of the cdp parser. Setting the Chroma Level Control This control sets the overall chroma level gain. To set the Chroma Level control, enter a value between to Everttz into the chroma level field. Setting the Line 21 Setup The Line 21 Setup control is used to set whether or not setup is removed from Line 21 of the incoming composite svertz signal.
Evertz s HD and more – Technische Informationsbibliothek (TIB)
Setting the White Clip Control Enabling the White Clip control forces the analog video decoder to clip all values above the level defined by the White Clip Level control. Disabling the White Clip control bypasses the clipping function. Setting the Blanking Controls — Field 2 The Blanking Controls for Field 2 enable the user to set what type of video processing will be applied to lines 10 through 23 of the incoming video signal.
Setting the Brightness The Brightness control allows the user to adjust the brightness of the analog video output. To set the brightness, enter a value between and 32 in the Video brightness field. To set the H blanking control, select either narrow or wide from the drop down menu. To set the Luma Wideband Frequency Response control, enter a value between -6 to 6.
Setting the VBI Efertz The Vertical Blanking interval may be passed through to the composite analog video output or everta be blanked. The HDx supports bi-level reference inputs only.
Setting the Test Signal Generator Output The user can select on which conversion path output the test signal generator is routed to. Note that there is a single test signal generator in the HDx.
If the test signal is active on a particular path output and it is then subsequently enabled on a different path, the test signal will be automatically disabled on the first path and enabled on the second path. In the HD, embedded audio from the video supplied to each of the four internal processing paths is de-embedded 16 channels and made available for subsequent processing. The following sections will outline in detail the parameters under each of these seven categories. This control enables the user to select an input channel from the Audio Mixer.
Enter an input gain between 0 and Audio Embedder Level 0 corresponds to mute dB. For the sake of brevity, the audio delay control for AES input channel 1 will be discussed in this manual.
For the sake of brevity, the audio sample rate converter status for AES IN 1 will be discussed in this manual. The total list of audio channel sources is dependant on aesOut the full set of audio options installed on the HDx. Select enable to invert the selected channel of audio and select Audio disable to pass through the selected audio channel.
For the sake of brevity, only the delay control for channel hd20014 will be described in this manual. Output Audio Mixer Revision 0.
evertz HD2014 Manuals
The total hd2041 of audio channel sources is dependant on analogOut the full set of audio options installed on the HDx Select one of the analogOut other options to have the analog audio outputs follow the OutputSource embedded audio outputs. Viewing the Product Name Accessing this menu item will display the entire name of evrrtz product. Factory Reset The Factory Reset menu item allows the user to reinstate the factory settings. Select the Factory Reset option if you wish to return the System configuration to its factory settings.
Evertz HD Manuals
Page of 91 Go. Page 15 – Figure Page 27 – Figure Fiber Inputs Page 33 – 3. Analog Audio Inputs Page 34 – 3. Page 38 – Adjusting the Video Proc for the Process The material contained in this manual consists of information that is the property of Evertz Microsystems and is intended solely for.
Evertz Microsystems expressly prohibits the use of this manual for any. No part of this publication may be reproduced without the express written permission of Evertz Microsystems.