manual, RUN/STOP, and alarms) and the PV or SV. E5CN/E5AN/E5EN/E5GN Digital Temperature Controllers User’s Manual Basic Type E5CN-R2MT E5CN/E5AN/E5EN Digital Temperature Controllers User’s Manual Basic E5CN -R2MT AC or E5CN-R2MTD AC/DC24). E5CN/E5CN-U Temperature Controller User’s Manual (Cat. No. H). E5CN Temperature Controller Communications User’s Manual (Cat. E5CN-R2MT-
|Published (Last):||8 February 2008|
|PDF File Size:||20.68 Mb|
|ePub File Size:||5.95 Mb|
|Price:||Free* [*Free Regsitration Required]|
Also, control output 2 can be set for use as an alarm output, to enable using up to three alarm outputs. Use the Temperature Controller within a power supply voltage and load that meet all specifications and ratings. If you remove the Controller from its case, do not touch or apply shock to the electronic parts inside.
E5CN-R2T manual datasheet & applicatoin notes – Datasheet Archive
Refer to the ntlp: A voltage output control output is not electrically insulated from the internal circuits. If an input error output is enabled, the a operation indication on the front panel will not light and s. Outputs will turn OFF depending on the mode when switching to the initial setting mode.
Therefore, the service life can be extended by lowering the temperature of the Temperature Controller. Panel interior dimensions for panel mounting? Long-life relay output available soon 2.
Locations subject to exposure to water or oil? Use the Temperature Controller within the following temperature and humidity ranges: Can be used for alarms to provide three alarm outputs. Recommended panel thickness is 1 to 5 mm. The terminal arrangement, terminal sizes, and depth for panel mounting have not been changed.
When two or more Temperature Controllers are mounted horizontally close to each other or vertically next to one another, the internal temperature will increase due to heat radiated by the Temperature Controllers and the service life will decrease. Plug Two, M3 depth: H Press the Level Key for at least 3 s. IEC Shaded settings are the default settings.
EUROTHERM ERO LFS Controller PID Heater Break Alarm Rs485 W/ Manual Hardware
An SELV circuit is one separated from the power supply with double insulation or reinforced insulation, that does not exceed 30 V r. You cannot move to other levels by operating the keys on the front panel from the calibration level.
Back-connecting Socket P3GA 27 dia. Keep the wiring for the Temperature Controller’s terminal block away from e5ch-r2mt-500 cables carry high voltages or large currents. Do not 14 use. Adjustment Level Press the Level Key less than 1 s.
Consult with your OMRON representative at any time to confirm actual specifications of purchased product.
These devices can cause radio disturbances which adversely affect the performance of the Controller. Option Units cannot be used for Plug-in models.
OMRON E5CN Datasheet: Ordering Information
The service life of electronic devices like Temperature Controllers is determined not only by the number of times the relay is switched but also by the service life of internal electronic components.
Pt or JPt Infrared temperature sensor: Can also be mounted to e5c-r2mt-500 DIN track. Set the alarm types for alarms 1 to 3 independently in the initial setting level. Insert the tool into the slots one on the top and one on the bottom and release the hooks. Locations subject to severe temperature changes? Install the appropriate switches f5cn-r2mt-500 circuit breakers and label them accordingly so that power can be turned OFF in an emergency by the person operating the Temperature Controller.
3 X c Manual Reset Thermostat Normal Closed Temperature Switch v 10a | eBay
Before inserting the Controller, confirm that the sealing rubber is in place. Tool insertion hole Flat-blade screwdriver Unit: Display flashes for at least 1 s. Do not use the Temperature Controller in locations subject to flammable or explosive gas.
Use and store the Temperature Controller within the rated ambient temperature and humidity. Some parameters may not be displayed depending on the protection settings and operation conditions.
Know and observe all prohibitions of use applicable to this product. Voltage outputs can be used for both heating and cooling for Models with Two Control Outputs. If the output relay is used beyond its life expectancy, its contacts may occasionally become fused or burned.
To reduce the danger or electric shock or fire, use the Temperature Controller in an controlled environment relatively free from polluting materials.