XE. XZE. XE. XZE. Industrial Label Printer | X-Series. dpi. dpi. Trusted Dependability, Quality Assured. Getting Started. Congratulations on choosing the Argox Xellent Series (X-Series) Enter Printer name (i.e. Argox X PPLB) and select “do not share this. ARGOX X is ideal for applications that require small labels or textile media. Provides greater productivity.
|Published (Last):||14 May 2011|
|PDF File Size:||4.88 Mb|
|ePub File Size:||1.98 Mb|
|Price:||Free* [*Free Regsitration Required]|
Dispose of used batteries according to the instructions. Insert the left side of dispenser bracket and secure the three screws to the TPH x-320. Lead the media through the print head module and under the paper sensor guide. Cleaning The Print Head After the related files have been copied to agox system, click “Finish”. Figure A Figure B Once the printouts as above appear, the possible cause may be the unequal positions of Ribbon Bracket, which needs to be adjusted properly to make its heights equally the same at both sides.
Release the button when the cutter starts cutting. The emulation is a printer programming language through which the host can communicate with your printer.
Guillotine Cutter With Paper Jam Don’t have an account? Argox Linux Printer Driver V1.
Figure 2 13 2 Head Latch Bracket 3. Lead the media backing paper through the print head module. Making a Barcode Reader Form 1. Unwrap the ribbon and separate the ribbon roll from the bare core. Figure 1 1 Backing Paper 24 2.
To print label the head latch must be closed. Programmable by command Data format: Find a Phillips screwdriver to lay down the blade by turning the screw counter-clockwise. Roll-feed, die-cut, continuous, fan-fold, tags, ticket in thermal paper or plain paper and fabric label. Windows Vista, Windows 7, Windows 8 and 8. Figure 1 Figure 2 76 B. Every time a media roll is printed, you should clean this compartment to reduce the incidence dust. Cleaning the Media Compartment Clean the media compartment with a cotton bud that has been moistened with a mild detergent.
The heavy duty is capable of 5ips print speed using its bit RISC microprocessor. W mm x H mm x D mm. From the leading end of the media roll remove enough labels to expose 6-inches of backing paper.
Argox X |
Figure 2 2 Print Head Module 3. Pin assignments are as follows: To change setting to ribbon would ink-side out, refer to Section – Switching Ribbon Wound Ink-side out or Ink-side in 1.
Centronics allows a much higher communication speed than serial. It’s a community-based project which helps to repair anything. Transmission Problems If the host shows “Printer Time out” 1.
Connect the x-33200 reader to the keyboard interface. During turning the Cam of cutter, release the blade from paper and them remove the paper from the cutter. Advanced Installation and Adjustment This chapter describes installation and adjustment procedure for X series industrial printers. Check the Cam as marked in Figure 1, find a slotted screwdriver to turn counter-clockwise as Figure 2.
ARGOX X Label Printer
In Dump mode, all characters will be printed in 2 columns: Clean the print head as follows: Open the top cover to access the print head module 3. Make a form for the keyboard. Please check Argox sales representative for most updated specifications.
Clockwise rotate the screw a half circle and test printing; observe whether the printing quality has been x-3200 improved or not; and stop the adjustment if the x-32200 is improved.
Argox X-3200 Manuals
Key-in the product name and number. The control knobs can rotate to both directions. These include pin assignments, protocols and detailed information about how to properly interface your printer with your host or terminal. The driver should now be installed.
Please contact your local Argox reseller if you need this cable. The printer now prints out a configuration report.
Repeat if necessary until the cotton is clean after it is passed over the head.